Tools and Equipment for Retubing Heat Exchangers, Boilers and HVAC Condensers-Elliott Tool Technologies

•	End Prep Systems
•	Retubing Tools
•	Rolling Motors / Torque Controls
•	Specialty Tools
•	Tube Cleaners
•	Tube Cutters
•	Tube Expanders
•	Tube Testers / Tube Plugs

Retubing Tools

Collet-Type Tube Puller
#M5360-00

Some customers say they can pull tubes in less than ten seconds, light-wall tubes
in five. Heavy wall tubes in thick tube sheets require more time to allow pump to develop the needed pressure.

Features
•	For pulling 1/2" through 1-1/2" O.D. tubes in seconds.
•	Automatically sets teeth to the same preset pressure every time.
•	Powerful 2 HP, 110 Volt industrial rated motor.
•	17 Ton Pulling capacity.
•	4000 PSI 20 ft. hydraulic hose connects the pump to the tube pulling cylinder assembly
•	Model M5733-00 for 230/1/50 electric applications.

Cyclegrip
# M5630-00

Features
•	For pulling 1/2" through 1"- O.D. ferrous and non-ferrous tubes
•	Small profile permits extraction of tubes close to the water jacket
•	Weight 16 lbs
•	Grippers exert 2-1/2 tons of force at 4,000 PSIG
•	Continuous 5 inch stroke operation as long as the pendant switch is depressed.
•	In continuous operation, a pulling rate of 120"/min. is produce

May be operated with Elliott M5360-00 or M5733-00 Hydraulic Power Unit or most hydraulic power units equipped with electrically operated hydraulic valves.

Pull Master
#M5735-00

Features
•	Requires no electric power
•	Extracts 3/8" through 1-3/4" O.D. Tubes
•	Ideal for use in oil refineries, chemical plants and sugar mills
•	Pulling rate is approx. 6.6 ft. per minute
•	90 PSI min air pressure required
•	80 cfm. min air volume required 80 cfm. Min
•	Automatic switching from speed pull mode to power pull mode depending upon resistance of the pulled tube
	30 ton pulling force is generated by a air over hydraulic intensifier

Spear Type Pullers

Spear-Type pullers are available with hand, electric and air powered hydraulic pumps. All Elliott Spear-Type Pullers have a 30 ton tube pulling capacity with a 6" pulling stroke.

80-36101 Hand Pump Tube Puller
Includes:
• 800MK1720 Ram Package
• 80-36101D3 Hand Pump
• PR-B7585-00 Safety Shield

80-36111 Electric Pump with Manual Directional Valve
Includes:
• 800MK1720 Ram Package
• 80PUJ1400B Electric Pump
• PR-B7585-00 Safety Shield

80-39999 Electric Pump with Electric Directional Valve
Includes:
• 800MK1720 Ram Package
• 80PER3405B Electric Pump
• PR-B7585-00 Safety Shield

80-36120 Air Pump with Manual Directional Valve
Includes:
• 800MK1720 Ram Package
• 80-13700 Air Pump
• PR-B7585-00 Safety Shield

Retubing Tool Accessories

Standard Knockout Tools

.680" dia shank x 2-3/8" length
Tube O.D.ranges available -1/2" to 1"

Tube Collapsing Tool
Tube Collapsing Tool

For tube sizes: 3/8" through 2 dia"
Sheet thickness 1-3/4" up to 4-1/4"

Tube Sheet Hole Brush

S/S or Nylon
Sizes Available - 1/4" to 1-1/4 dia."

Flaring Tool

Hand or Pneumatic Hammer Use
Tube O.D. ranges available-1/4" to 2 dia"

Belling Tool

Hand or Pneumatic Hammer Use

Pneumatic Beading Tool
Pneumatic Beading Tool

.680" dia shank.x 6.0"
Hand or Pneumatic Hammer Use

Tube Rolling Lubricant

Tube Rolling Lubricant

Available sizes-quart, gallon or 5 gallon
Two compounds available

Pneumatic Hammer

Pneumatic Hammer

Used with Knockout, Collapsing and Beading Tools

Tube Gage

Features
•	Nine sizes - for tubes from 1/2" to 1-1/4" O.D. (12 to 37 mm)
•	Design uses extensions instead of being a fixed length reduces your need to buy multiple units for different lengths.
•	Dial reads in thousandths of an inch or millimeters.
•	Takes the feel and guesswork out of measuring tubes

To receive more information about the above products, please call, fax, e-mail or use our Inquiries page